SPL Performer s1200 Stereo Power Amplifier

The powerful stereo amplifier
This impressive stereo power amplifier leads even the most demanding speakers to soundscapes beyond your expectations. With a power amplification of 2 x 520 W (4 Ω) [2 x 550 W (2 Ω); 2 x 300 W (8 Ω)], this amplifier easily controls any loudspeaker. Thanks to the VOLTAiR technology the performance of the s1200 is detail-rich, vivid, honest and plain simply beautiful.

Individual design
In addition to the choice of the basic colour black, red or silver, there are further options for customising the Performer s1200 to individual design preferences. Nine different colour combinations can be realised with the black, red and silver decorative panels included in the scope of delivery. The decorative panels adhere with the help of a strong neodymium magnet. No tools are required to exchange them.

Better safe than sorry
The Performer s1200 has a protection circuit against DC voltage and against overheating. If direct current (DC) is detected, the output stage switches off automatically and the Protect LED lights up red. To protect the s1200 against the unlikely event of overheating, a temperature sensor at the heatsinks continuously monitors the temperature of the device. The TEMP LED lights up yellow when the Performer s1200 is getting too hot. As a result of this the output stage is switched off and the fans run on high-speed until the device has cooled down.

Freedom of choice
The Performer s1200 features a stereo pair of XLR and RCA inputs. This makes it compatible with all preamps on the market without the use of adapters. The corresponding stereo input can be selected via the Input Select switch on the rear panel.

Trim to fit
With reference to the Performer s1200, “fit” means adapted. You can adapt the input sensitivity in 0.5 dB steps from 0 dB to -5.5 dB. In contrast to a panorama potentiometer in a preamplifier, this trim switch is the more audiophile solution. The optimal operating range of the loudspeakers and preamplifier can be perfectly adjusted this way.

Plus & Minus
The loudspeaker binding posts can accommodate banana plugs as well as a stranded wire with a diameter of up to 4 mm. No loudspeaker with less than 2 ohms impedance shall be connected.

AMP CTL
The standby mode of the power amplifier can be switched on and off using the AMP CTL connection between a preamplifier such as the Director Mk2, Elector, Phonitor x or the Crossover. To do this, connect the 3.5 mm phone jacks with a cable with 3.5 mm mono or stereo jack plugs. Thanks to its 12 V trigger input, third party preamps can also switch the Performer s1200's standby mode on and off.

A class of its own
Conventional solid-state power amplifiers tend to operate in a critical range of the built-in components, this results in unpleasant harmonical artifacts. Tube power amplifiers also distort at their limit but their characteristical behaviour softens this roughness and harshness. Non the less this is a falsified representation of the sound image. Thanks to VOLTAiR Technology, the Performer s1200 can process much higher levels without even coming near to a critical range. All components constantly operate in the optimal range. The result is a very pleasant, natural and relaxed sound experience. Enjoy your music in every detail and without any listening fatigue.

Full power
The Performer s1200 features individual amplification stages for voltage and power amplification, which ensures a perfect
operating of the class-AB amplifier circuit. Thanks to each stage's own negative feedback path, it is ruled out that feedbacks from the loudspeaker are interacting with the input stage, this way the SPL VOLTAiR Technology can play out its full performance.

Keep cool
Inside the Performer s1200, six fans usually do nothing at all, because 90 % of the heat is passively dissipated via massive
heat sinks. Should it nevertheless become really loud for a really long time, the processor-controlled fans remain virtually
inaudible at only 19 dB (A). During power-up, the fans of the Performer s1200 briefly rotate at a higher speed to remove
dust of themselves and surrounding components.